Rabbit cages are places where rabbits live. Making a good rabbit cage not only contributes to the healthy growth of rabbits, but also reduces feed and labor costs. According to the author's practice and summarizing the experiences of many rabbit farmers, we now have a few opinions on the production of rabbit cages for everyone, especially readers who are ready to make rabbit cages.
(A) Specifications: Rabbit cage 40 cm high, 78 cm high, 60 cm deep before and after, left and right 55 cm wide, this specification can basically meet the needs of a variety of adult rabbits. The bottom of the cage is not less than 25 cm above the ground, and the distance between the upper cage and the lower cage is 10 cm, followed by 12 cm, and the number of layers is not more than 3 layers. The total height (the distance from the upper floor of the upper cage) is about 185 cm. Too high is not only a waste of material, but also is not conducive to observation, feeding and cleaning.
(2) Materials: The cage wall is cast with cement and sand (the ratio of cement, fish sand and gravel is 1:2:3). The cement board should be smooth and strong, not hang hair, bite resistance, thickness 4 cm. The front door is made of steel (with bamboo bite resistant) and the spacing between bars is 3 cm. The backboard is made of cement and sandstone, with 3 empty spaces in the middle and 3cm in neutral density. The low plate is made of bamboo pieces. The width of the bamboo piece is about 3cm. There is no gap between the 1/3 and 1/2 of the front part. The gap between the rear 1/3 and the 1/2 piece of bamboo is 1cm (if the rabbit is found in the front defecation. , Can put a brick in the defecation site to occupy the position until the rabbit to the rear defecation to take away the brick). The floor should not be designed as a fixed type and should be withdrawn at any time for repair and cleaning. The excrement board is casted with cement and gravel with a thickness of 3 cm. The interior can generally not be reinforced. The length of the bottom layer (that is, the cover of the bottom cage) is 75 cm and the middle layer is 77 cm. When installed, the wall of the cage is 5 cm in front of the door. In this way, the feces and urine discharged from the upper layer do not contaminate the lower layer.
(3) Installation of drinking fountains: The automatic drinking fountain is installed on the backboard, and the water pipes are parallel to the outside (rabbit catches and bites the water pipe). Such as self-made drinking fountains, it should be hung on the front door, easy to observe the water level and timely replenishment.
(d) Installation of cartridges: The cartridges are best made out of the box. When the rabbit eats material, the head can not protrude from the reinforced door and it is also convenient for artificial feeding. It is also possible to place the cartridge in the door, but to maintain a certain height to prevent rabbits from digging.
(5) Metal cages are not used as much as possible: Metal cages are mostly made of galvanized steel wire drawn from cold drawn steel wire. This brings with it four problems. First, it is prone to rust, and it will be eliminated in a few years. In the long run, the cost is lower. Big. The second is that the bottom of the tool cage is fixed as a whole, and it is difficult to clean up once it has been stuffed with coarse material and feces. Third, when the front and back sides of the installation are installed with steel reinforcement bottoms, it is very inconvenient to fix and replace them. Fourth, the rabbit's foot contact surface is small, rabbits are prone to foot dermatitis when in contact with the metal, and once the foot dermatitis is difficult to cure
(A) Specifications: Rabbit cage 40 cm high, 78 cm high, 60 cm deep before and after, left and right 55 cm wide, this specification can basically meet the needs of a variety of adult rabbits. The bottom of the cage is not less than 25 cm above the ground, and the distance between the upper cage and the lower cage is 10 cm, followed by 12 cm, and the number of layers is not more than 3 layers. The total height (the distance from the upper floor of the upper cage) is about 185 cm. Too high is not only a waste of material, but also is not conducive to observation, feeding and cleaning.
(2) Materials: The cage wall is cast with cement and sand (the ratio of cement, fish sand and gravel is 1:2:3). The cement board should be smooth and strong, not hang hair, bite resistance, thickness 4 cm. The front door is made of steel (with bamboo bite resistant) and the spacing between bars is 3 cm. The backboard is made of cement and sandstone, with 3 empty spaces in the middle and 3cm in neutral density. The low plate is made of bamboo pieces. The width of the bamboo piece is about 3cm. There is no gap between the 1/3 and 1/2 of the front part. The gap between the rear 1/3 and the 1/2 piece of bamboo is 1cm (if the rabbit is found in the front defecation. , Can put a brick in the defecation site to occupy the position until the rabbit to the rear defecation to take away the brick). The floor should not be designed as a fixed type and should be withdrawn at any time for repair and cleaning. The excrement board is casted with cement and gravel with a thickness of 3 cm. The interior can generally not be reinforced. The length of the bottom layer (that is, the cover of the bottom cage) is 75 cm and the middle layer is 77 cm. When installed, the wall of the cage is 5 cm in front of the door. In this way, the feces and urine discharged from the upper layer do not contaminate the lower layer.
(3) Installation of drinking fountains: The automatic drinking fountain is installed on the backboard, and the water pipes are parallel to the outside (rabbit catches and bites the water pipe). Such as self-made drinking fountains, it should be hung on the front door, easy to observe the water level and timely replenishment.
(d) Installation of cartridges: The cartridges are best made out of the box. When the rabbit eats material, the head can not protrude from the reinforced door and it is also convenient for artificial feeding. It is also possible to place the cartridge in the door, but to maintain a certain height to prevent rabbits from digging.
(5) Metal cages are not used as much as possible: Metal cages are mostly made of galvanized steel wire drawn from cold drawn steel wire. This brings with it four problems. First, it is prone to rust, and it will be eliminated in a few years. In the long run, the cost is lower. Big. The second is that the bottom of the tool cage is fixed as a whole, and it is difficult to clean up once it has been stuffed with coarse material and feces. Third, when the front and back sides of the installation are installed with steel reinforcement bottoms, it is very inconvenient to fix and replace them. Fourth, the rabbit's foot contact surface is small, rabbits are prone to foot dermatitis when in contact with the metal, and once the foot dermatitis is difficult to cure
Our Microscope Products is good in quality and competitive in price. We are manufacturer and supplier Microscope Products following your specific requirement. We are looking forward to your E-mail and establishing cooperative relationship with you! We would provide professional Microscope with good services for you!
Microscope
Compound Microscopes, Metallurgical Microscope, Biological Microscopes, Optical Microscopes
Ningbo Cland Medical Instruments Co., Ltd. , http://www.ruipumedical.com