Secure installation against loosening When installing a hammer-type feed kneader, the base with the machine should be placed on a flat concrete floor. The kneader is firmly mounted on the base with bolts, and the position of the motor is constantly adjusted to ensure that the motor pulley groove is aligned with the main pulley groove, and a moderate degree of belt tension is obtained. It must be noted that all electrical equipment and wiring should be safe and reliable, and all moving parts of the machine after installation must be flexible and can be put into use after no air jams or abnormal noises.
Strict operation and failure prevention
1, before the operation. The operator must be familiar with the structure and performance of the machine in advance, and check the unit as follows: The fasteners of each part must not be loosened; check the degree of hammer wear to determine whether to replace; whether the split pin has a fracture phenomenon, if there is a break, timely Replace; Clear the plug in the machine; Spindle rotation is flexible, there should be no collision and friction; drive belt must be installed protective cover; carefully remove the material in the stone, iron, etc., to prevent damage to the machine parts.
2, when processing operations. After starting the machine, the standby machine must be running smoothly before starting work. When working, the operator should stand on the side of the feed inlet to prevent hard objects from being ejected from the feed inlet. When feeding, high-speed rotating hammers have a very good gripping ability. Therefore, they must be fed evenly to prevent excessive feeding, resulting in overloading and jamming. If clogging occurs, the material should be pulled out and re-fed. Feeding with iron bars is prohibited. The operator must not leave the job during the work process. If the machine has abnormal sound, stop the machine immediately to check and troubleshoot. Do not open the housing during operation to check and adjust the machine.
Timely adjustment of maintenance After the completion of each shift, it is necessary to cut off the power in a timely manner, clean the inside of the machine, and check whether the fasteners are loose and tighten immediately if loose. Every 30 hours of operation, two bearings need to be greased once. After working for 300 hours, clean the bearing oil and refill with grease. Always check the wear of the hammer. After the hammer has been used for a period of time, it can be used interchangeably according to the condition of rounding of edges and corners. If all 4 corners have been worn out, replace the new one. In addition, the tension of the transmission tape should also be regularly checked and adjusted in time. If the machine is used in the open air, it should also have rain protection facilities.
Strict operation and failure prevention
1, before the operation. The operator must be familiar with the structure and performance of the machine in advance, and check the unit as follows: The fasteners of each part must not be loosened; check the degree of hammer wear to determine whether to replace; whether the split pin has a fracture phenomenon, if there is a break, timely Replace; Clear the plug in the machine; Spindle rotation is flexible, there should be no collision and friction; drive belt must be installed protective cover; carefully remove the material in the stone, iron, etc., to prevent damage to the machine parts.
2, when processing operations. After starting the machine, the standby machine must be running smoothly before starting work. When working, the operator should stand on the side of the feed inlet to prevent hard objects from being ejected from the feed inlet. When feeding, high-speed rotating hammers have a very good gripping ability. Therefore, they must be fed evenly to prevent excessive feeding, resulting in overloading and jamming. If clogging occurs, the material should be pulled out and re-fed. Feeding with iron bars is prohibited. The operator must not leave the job during the work process. If the machine has abnormal sound, stop the machine immediately to check and troubleshoot. Do not open the housing during operation to check and adjust the machine.
Timely adjustment of maintenance After the completion of each shift, it is necessary to cut off the power in a timely manner, clean the inside of the machine, and check whether the fasteners are loose and tighten immediately if loose. Every 30 hours of operation, two bearings need to be greased once. After working for 300 hours, clean the bearing oil and refill with grease. Always check the wear of the hammer. After the hammer has been used for a period of time, it can be used interchangeably according to the condition of rounding of edges and corners. If all 4 corners have been worn out, replace the new one. In addition, the tension of the transmission tape should also be regularly checked and adjusted in time. If the machine is used in the open air, it should also have rain protection facilities.
Goji Berry powder is a convenient, highly concentrated form of the world's most powerful anti-aging food. Goji berries are believed to enhance the immune system, protect eyesight, and support the liver. Made from wild goji berries, this powder can be mixed with water to make Goji Juice. Enjoy it in smoothies and teas for a superior boost of antioxidants and other nutrients.
Goji Powder,Goji Powder Benefits,Goji Powder Bulk,Goji Powder Nutrition
Ningxia Rich Resource International Co., Ltd , http://www.richresources-nx.com