Cold drink machine / hot and cold drink juice machine use and characteristics
The cold drink machine can make all kinds of hot and cold drinks such as hot and cold milk, juice, etc. It is easy to use and clean and is an ideal equipment for the catering industry. The cold drink machine adopts stainless steel evaporator, which has good heat transfer effect and fast lifting speed. The cold drink machine has the advantages of small size, light weight, low power consumption, and convenient operation.
1. Please place it on a solid counter in a horizontal manner. If the counter is tilted or uneven, the machine will malfunction. Please pay special attention.
2. Be sure to install the grounding wire and leakage protection switch.
3. Please do not insert the rod with your hand or fine root into the machine. This is because if the motor is rotating, it can be dangerous.
4. Check the wires before or during use.
5. Please wash the beverage tank every day to keep it clean.
6. If it is restarted after shutdown, it must be separated by more than 5 minutes. The voltage is unstable and equipped with a voltage regulator of 2000W or more.
7. Please install a good place for ventilation equipment. There must be around the machine.
8. Please use the mechanical special plug, do not use a socket together with other electrical appliances.
9. Please install in the ambient temperature below 35 degrees, the temperature of the beverage should not exceed 40 degrees when cooling.
10. It is strictly forbidden to switch to cooling or heating working state when heating or cooling working, otherwise the compressor will be damaged.
Cleaning and operating instructions
1. The machine first sets the large apron in the original shape on the cylinder. The sealing ring must be laid flat, and then the evaporator is vertically downward. Pay attention to the pump body to be flattened vertically downwards. It must be cleaned and disinfected before use. The specific steps are as follows:
1) Remove the madness gently
2) Hold the spray water pump by hand, gently pull it up and rotate the spray pipe and then pull it out (spray) to remove the stirring blade from the stirring support sleeve by hand (stirring). Note: Do not forget to install the seal ring. .
3) After the above parts are removed, slowly swing the hands up and out of the tank. If you have difficulty, it is necessary to wet the stainless steel evaporator and gasket. After cleaning the removed parts, reinstall them and operate them in the opposite way. Note: Do not use hot water above 80 °C when cleaning the plastic and rubber parts of the machine to avoid damage to the parts.
2, start work: when all the components are installed, the beverage is filled, when using the heating function, it must be filled
(1) Press the fountain/mixing series switch first, then press the cooling switch upwards, the machine enters the cooling state, the temperature is below 5 degrees Celsius, close to 0 degrees Celsius.
(2) If heating is required, first press the fountain/stirring switch to adjust the temperature to the temperature you need. If one of the cylinders is not required to be heated, the temperature controller of the cylinder should be adjusted to the stop position, and the temperature you need can be adjusted individually for each cylinder depending on the situation.
Cold drink machine - basic concept
A cold drink machine is a machine that mechanically presses fruits or vegetables into cold drinks and cold drinks.
The cold drink machine is a kind of hot and cold drink juice machine. In addition to the cold drink machine, there is a hot drink machine, a hot and cold drink machine.
Cold drink machine - how to use
1. Screw the cutter and the centrifugal filter tightly before use, and then fasten the upper box of the centrifugal filter and the cutter to the base, and then turn on the power;
2. After the motor rotates normally, the food is placed;
3, the amount of food should not be too large, too thick, too hard, so as not to damage the cutting knife and cause the motor to overload;
4. Do not store too much food in the centrifugal filter. It should be cleaned in time, otherwise it will cause vibration; keep the juicer clean inside and outside. Wash carefully after each use. However, when cleaning, do not rinse with the tap, the base of the lower part of the juicer, and do not put the body in the water, so as to prevent the insulation part of the electrical part from being damaged.
Cold Drink Machine - Product Category
The cold drink machine is divided into three categories, a blender, a single-function juicer, and a multi-function juice blender.
1. Special for electric oranges
This type of cold drink machine is a machine for pressing out water-cooled drinks, such as oranges, grapefruits or lemons.
This kind of machine can be used to mix softer fruits and stir them into a mud. It is very versatile. It can be used in home cooking in addition to cold drinks.
This is because some fruits and vegetables have more fiber components, such as sugar cane and carrots. Therefore, the juicer can utilize the effect of high-efficiency separation to separate the cold drink and the residue, and more fully and effectively help the body to absorb the nutrients of fruits and vegetables. .
4, multifunctional fruit and vegetable juicer
The combination of cold drink machine, juicer, grinder, and soya-bean milk machine, multi-functional design, is in line with the economic benefits of modern people.
Juice machine processed food type:
It is suitable for making various beverages such as juice, soy milk and coconut milk with different degrees of heat and cold.
Juice machine introduction:
1, PL
2, PL117TM: high-quality and high-efficiency compressor, refrigeration and heating can be adjusted at will, built-in heating can produce milk, soy milk, magnetized water function, ultra-transparent beverage barrel cover, double-layer insulation.
Cold drink machine processed food type:
It is suitable for making various beverages such as juice, soy milk and coconut milk with different degrees of heat and cold.
Introduction to the cold drink machine:
1, PL
2, PL234TM: high-quality high-efficiency compressor, refrigeration and heating can be adjusted at will, built-in heating can produce milk, soy milk, magnetized water function, ultra-transparent beverage can lid, double-layer thermal insulation lid, heating temperature can be adjusted separately.
Cold drink mechanic food type:
It is suitable for making various beverages such as juice, soy milk and coconut milk with different degrees of heat and cold.
Introduction to the cold drink machine:
1, PL
2, PL351TM: high-quality high-efficiency compressor, refrigeration and heating can be adjusted at will, built-in heating can produce milk, soy milk, magnetized water function, ultra-transparent beverage can lid, double-layer thermal insulation lid, heating temperature can be adjusted separately.